Model/Brand/Package
Category/Description
Inventory
Price
Data
-
![]()
Category: Classification of electronic componentsDescription: Two way, direct control type, liquid CO2 valves These valves are two-way direct control solenoid valves used for liquid CO2. Suitable for high-pressure applications, with a minimum working pressure of 0 bar, normally closed and threaded port connection. The brass body does not require pressure during operation, and the DIN plug connection is tight and lightweight. It can be installed in any position9763 -
![]()
Category: Classification of electronic componentsDescription: 0 bar，Normally closed, threaded port connection. Brass body does not require minimum working pressure, tight and lightweight DIN plug connection can be installed at any position # # # 2 and 3 corrosive gas and fluid valves5790 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, directional type, minimum pressure, normally closed valve, 2-way directional solenoid valve, requiring minimum working pressure, normally closed, with threaded port connection. The minimum working pressure requirement for brass body is tight and lightweight. DIN plug connection temperature range: -20 to+85 ° C can be installed in any position. The pressure range is suitable for water and may vary for other media. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.15341+$2644.601310+$2620.559525+$2608.538650+$2596.5176100+$2584.4967150+$2572.4758250+$2560.4549500+$2548.4340 -
![]()
Category: Classification of electronic componentsDescription: Two way, normally closed, two-way air/combustion control valve, direct control type, EN161 certified solenoid valve, suitable for air and gas combustion control, minimum working pressure of 0 bar, normally closed and threaded port connection. No pressure required during operation, compact and lightweight ISO 4400 DIN connection Class A, 2 sets of service and gas series 1 and 2 can be installed in any position. # # # Recognized EN161 small solenoid valve, suitable for most gas and fluid handling applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.1661 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, direct control type, zero pressure, normally closed valve with 2 channels, direct acting solenoid valve, normally closed, threaded port connection brass body. No pressure required for tight and lightweight DIN plug connection during operation. Temperature range: -10 ° C to+100 ° C can be installed at any position. Pressure range is suitable for water and may vary for other media. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.9024 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, direct control type, high pressure, normally closed valve, direct control type solenoid valve, with stainless steel or brass body and NBR rubber seal. Equipped with manual override, suitable for air, inert gas oil, and water. ASCO's 262 series process valves comply with ROHs standards and do not require minimum pressure to operate. The coil can easily switch between AC and DC. Provide normally open or normally closed. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.2367 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, directional type, minimum pressure, normally closed valve, 2-way directional solenoid valve, requiring minimum working pressure, normally closed, with threaded port connection. The minimum working pressure requirement for brass body is tight and lightweight. DIN plug connection temperature range: -20 to+85 ° C can be installed in any position. The pressure range is suitable for water and may vary for other media. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.2034 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, directional type, minimum pressure, normally closed valve, 2-way directional solenoid valve, requiring minimum working pressure, normally closed, with threaded port connection. The minimum working pressure requirement for brass body is tight and lightweight. DIN plug connection temperature range: -20 to+85 ° C can be installed in any position. The pressure range is suitable for water and may vary for other media. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.4390 -
![]()
Category: Classification of electronic componentsDescription: 0 bar，Normally closed, threaded port connection. Brass body does not require minimum working pressure, tight and lightweight DIN plug connection can be installed at any position # # # 2 and 3 corrosive gas and fluid valves5033 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, stainless steel normally closed valve, 2-way stainless steel solenoid valve, minimum working pressure 0 bar, normally closed, threaded port connection. Stainless steel body can be operated without pressure, with a tight and lightweight DIN plug connection temperature range of -25 to+85 ° C. It can be installed at any position. The pressure range is suitable for water, unlike other media. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.9982 -
![]()
Category: Classification of electronic componentsDescription: DIN The plug can be adjusted between 2 and 40 seconds during connection and between 0.5 and 45 minutes during disconnection, with a protection level of IP65. It is suitable for air, inert gas, water, and oil. ###Drainage and drain valve6955 -
![]()
Category: Classification of electronic componentsDescription: 2-Way Barbed Solenoid Air Valve - Normally Closed76761+$55.411210+$52.2319100+$49.8701250+$49.5067500+$49.14341000+$48.73462500+$48.37125000+$48.1441 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, direct control type, high pressure, normally closed valve, direct control type solenoid valve, with stainless steel or brass body and NBR rubber seal. Equipped with manual override, suitable for air, inert gas oil, and water. ASCO's 262 series process valves comply with ROHs standards and do not require minimum pressure to operate. The coil can easily switch between AC and DC. Provide normally open or normally closed. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.6407 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, direct control type, high pressure, normally closed valve, direct control type solenoid valve, with stainless steel or brass body and NBR rubber seal. Equipped with manual override, suitable for air, inert gas oil, and water. ASCO's 262 series process valves comply with ROHs standards and do not require minimum pressure to operate. The coil can easily switch between AC and DC. Provide normally open or normally closed. ###2-way inert gas and fluid valve small solenoid valve, suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.5733 -
![]()
Category: Classification of electronic componentsDescription: 3 Road, direct control type valve, normally closed direct control type solenoid valve, with stainless steel or brass body and NBR rubber seal. Equipped with manual override, suitable for air, inert gas oil, and water. ASCO's 314 series solenoid valves provide a compact solution for controlling single acting actuators or filling and drainage systems. ###Features and advantages: Compact valve designed for single acting actuator control of high working speed. The valve is optimized for general 3-way directional applications, with only one spring and two moving parts that comply with RoHS. These valves do not require a minimum working pressure to meet all relevant EC directives. Installation can be installed in any position without affecting the operation of the solenoid valve. The main body of the valve has 2 installation holes and a 1/4 (G) pipe connection. It has standard combination threads and complies with ISO 228/1 and ISO 7/1 standards. The pipeline connection G 1/8 has standard threads and complies with ISO 228/1 standard. Each valve comes with installation/maintenance instructions # # # 3-way inert gas and liquid valve small solenoid valve, suitable for most gas and fluid handling applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil is powered off, the spring (or servo assist device) re controls the valve, as described on the right side of the diagram. Please refer to the typical schematic diagram below. The 2/3 way design indicates that the valve has three ports and two working modes. Usually, 2/2 valves are referred to as 2-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameter6354 -
![]()
Category: Classification of electronic componentsDescription: 3 Road, direct control type valve, normally closed direct control type solenoid valve, with stainless steel or brass body and NBR rubber seal. Equipped with manual override, suitable for air, inert gas oil, and water. ASCO's 314 series solenoid valves provide a compact solution for controlling single acting actuators or filling and drainage systems. ###Features and advantages: Compact valve designed for single acting actuator control of high working speed. The valve is optimized for general 3-way directional applications, with only one spring and two moving parts that comply with RoHS. These valves do not require a minimum working pressure to meet all relevant EC directives. Installation can be installed in any position without affecting the operation of the solenoid valve. The main body of the valve has 2 installation holes and a 1/4 (G) pipe connection. It has standard combination threads and complies with ISO 228/1 and ISO 7/1 standards. The pipeline connection G 1/8 has standard threads and complies with ISO 228/1 standard. Each valve comes with installation/maintenance instructions # # # 3-way inert gas and liquid valve small solenoid valve, suitable for most gas and fluid handling applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil is powered off, the spring (or servo assist device) re controls the valve, as described on the right side of the diagram. Please refer to the typical schematic diagram below. The 2/3 way design indicates that the valve has three ports and two working modes. Usually, 2/2 valves are referred to as 2-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameter8311 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, direct control type steam valve, direct control type solenoid valve, with brass body, designed for steam and hot water applications. High temperature coils and PTFE seals ensure long lifespan and maximum reliability. Normally closed operation.2510 -
![]()
Category: Classification of electronic componentsDescription: 2 Up to 40 seconds, adjustable disconnect period of 0.5 to 45 minutes, adjustable to be directly installed on any solenoid valve with ISO 4400 DIN connection, directly installed between the coil and power connector, 24 to 240 V DC or AC (50/60 Hz) medium temperature from -10 to+50 ° C # # # Standard CSA # # Timer for Solenoids46301+$1125.775210+$1115.540925+$1110.423750+$1105.3066100+$1100.1894150+$1095.0722250+$1089.9551500+$1084.8379 -
![]()
Category: Classification of electronic componentsDescription: 2//2 and 3//2 base-mounting solenoid valves Range of solenoid valves series 108 2//2 NF and 109 3//2 NF for base mounting. Compact and lightweight for easy installation. No minimum control pressure. Standard manual control. Polyphenylene sulphide (PPS) body shell Pluggable connectors. 2 Inert gas and fluid valves are small solenoid valves suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.4690 -
![]()
Category: Classification of electronic componentsDescription: 2 Road, directional type, zero pressure, normally closed valve, 2-way directional solenoid valve, minimum working pressure 0 bar, normally open, threaded port connection brass body, no pressure required for tight and lightweight DIN plug connection, can be installed at any position. The pressure range is suitable for water and may vary for other media. Small solenoid valves are suitable for most gas and fluid processing applications. The schematic diagram illustrates the (circuit) functions of various solenoid valves. This diagram is developed in layers, and the left side of the diagram is sufficient to describe the operating condition of the valve when the coil is energized. When the coil loses power, the spring (or servo assist) re controls the valve, as described on the right side of the diagram. The 3/2-way design indicates that the valve has three ports and two operating modes. Usually, 2/2-way valves are referred to as two-way valves. The schematic diagram uses A, B, P, P1, P2, and R port markings, which are also indicated on the valve body. The valve body is usually marked for specific line functions and can also be used for other purposes. The schematic diagram and technical parameters will indicate the corresponding connections and pressure performance that require alternative circuit functions.5950 -
![]()
Category: Classification of electronic componentsDescription: DIN The plug can be adjusted between 2 and 40 seconds during connection and between 0.5 and 45 minutes during disconnection, with a protection level of IP65. It is suitable for air, inert gas, water, and oil. ###Drainage and drain valve8815
