Model/Brand/Package
Category/Description
Inventory
Price
Data
-
![]()
Category: Classification of electronic componentsDescription: DTM - Temperature display device Display unit for measurement range -100°C to +1100°C For type-K thermocouples Suitable plug: K-miniature cable plug Resolution: | 1 °C ---|--- Operating temperature: | 0 °C → +50 °C Housing Dimensions (H x W x D): | 123 x 72.5 x 27.5 mm ### Without reason34461+$1032.517410+$996.288750+$991.7601100+$987.2315150+$979.9858250+$973.6458500+$967.30581000+$960.0600 -
![]()
Category: Classification of electronic componentsDescription: LKM 262 The digital programmable measurement converter LKM 262 is a digital programmable measurement converter suitable for installation on standard rails. This converter is programmable and suitable for different thermocouples, complying with DIN EN 60584-3 standard. LKM 262 linearly converts the temperature dependent thermoelectric voltage of the sensor into a standard signal. Signal range: 0 to 10V. Temperature compensation is effective within the measurement converter itself. The measurement converter can be programmed using the universal interface LKM S1 provided by RS. Adjusting the controller allows for immediate small display corrections. Input: Thermocouples K, J, L, T, U, E, N, S, B, R, C (within the corresponding defined range) Zero: -200 to 600 ° C *, depending on thermocouple range: 50 K Linear error: 0.3K, depending on thermocouple measurement error: 0.2% Reference contact error:+/-0.5 ° C Power supply voltage: 15 to 35V DC, 15 to 26V AC, polarity reversal protection Maximum current consumption: 20mA Output: 0 to 10V, programmable sensor fault: 10V Short circuit: Voltage value at room temperature Response time: 0.5s TC: 100ppm/° C Operating temperature range: -40 to 85 ° C Humidity: 95% Installation: 35mm DIN rail Shell: Polycarbonate 75x25x53mm Terminal Type: Screw Terminal Clamping Range: 0.2 to 2.5mm ² Weight: Approximately 60g Vibration: 5g/10 to 200Hz # # # Note LKM S1 universal interface, please refer to RS Inventory Number 9130857 # # # Recognized EMC Radiation and Noise Resistance: EN 61326-1:2006 EN 61326-2-3:2006 # # Temperature Transformer23261+$537.806710+$523.777050+$513.0208100+$509.2796200+$506.4736500+$502.73241000+$500.39412000+$498.0558 -
![]()
Category: Classification of electronic componentsDescription: Joining sensor for pipe diameters 20 mm → 110 mm, temperature range 0 °C → +200 °C Joining sensor for pipe diameters 20 mm → 110 mm Working temperature range 0 °C → 200 °C Temperature sensor: | 1 x Pt100 cl. B ---|--- Connection: | 2-ltr. circuit Temperature range: | 0°C → 200°C Connecting cable: | 2500 mm TeSi 2 x 0.34 (180°C) Mounting strap: | In the range 20 to 110 mm ### probe4447 -
![]()
Category: Classification of electronic componentsDescription: LKM445/446 The indoor temperature and humidity sensor LKM 445/446 is a low-cost internal temperature and humidity sensor with an integrated measurement converter and two voltage outputs. This sensor allows users to measure temperature and humidity levels in buildings, factories, and switchgear. This temperature sensor can be directly connected to evaluation devices that also have voltage inputs, such as PC cards or PLCs, and is fully calibrated when supplied. The temperature accuracy of LKM 445/446 sensors is+/0.5 ° C, and the relative humidity accuracy is 3%. Comes with two controllers, allowing users to perform minor corrections on site. Sensors are only suitable for enclosed spaces, and special attention should be paid to their placement when installing them. There is a cable outlet on the back of the sensor, and the side cable outlet is an available option. This temperature/humidity sensor has a protection level, and users can choose to switch to a temperature range of -20 to 80 ° C. Input: Integrated semiconductor sensor Temperature measurement range: 0 to 50 ° C can be switched to -20 to 80 ° C Humidity measurement range: 0 to 100% Relative humidity Guarantee value 5 to 95% Temperature measurement error: Typical+/-0.5 ° C @ 25 ° C Humidity measurement error: 3% Operating temperature range: -20 to 80 ° C Humidity: 95% Terminal type: Screw clamp clamping range: 0.13 to 1.5mm2 Material: PVC White size: 70x70x25mm (height x width x thickness) Weight: Approximately 50g Protection level: IP20 # # # # Recognized EMC radiation and noise resistance: EN 61326-1:2006 EN613266 2-3:2006 # # Installation Sensor61911+$897.899310+$866.394150+$862.4559100+$858.5178150+$852.2167250+$846.7033500+$841.18991000+$834.8889 -
![]()
Category: Classification of electronic componentsDescription: Type 259 thermocouple for high mechanical loads, type K and J Screw-in thermocouple with replaceable measuring insert, e.g. for exhaust gas measurement in ship diesel engines Protection rating IP 54in accordance with DIN 40 050 Anti-kink spring Temperature sensor: | 1 x K or 1 x J ---|--- Temperature range: | to 1200℃ (type K) or 900℃ (type J) Installation length: | 100 or 200mm Protective tube material: | 1,4571 stainless steel Connecting cable: | 2500mm SiSi 2 x 1.5mm Thread: | G1 / 2A87651+$1836.850410+$1820.151825+$1811.802450+$1803.4531100+$1795.1038150+$1786.7545250+$1778.4052500+$1770.0558 -
![]()
Category: Classification of electronic componentsDescription: LKM455/456 The outdoor temperature and humidity sensors LKM 455/456 are low-cost options with integrated measurement converters, including two voltage/current outputs. This sensor can measure temperature and humidity values inside buildings, factories, and switchgear. LKM 455 and 456 can be directly connected to evaluation devices with voltage output, such as PC cards or PLCs. The typical accuracy of these temperature and humidity sensors is+/-0.5 ° C and 3% relative humidity. The sensor was fully calibrated upon delivery. Provide two controllers for performing smaller on-site corrections. The design of these sensors is suitable for enclosed spaces and outdoor areas. When installing KLM 455 and 456, it is necessary to pay attention to correctly placing the sensors. These temperature and humidity sensors have a protection level of IP64 and a measurement range of -20 to 80 ° C for temperature and 0 to 100% for relative humidity. Users can switch to a temperature range of 0 to 50 ° C. Input: Integrated semiconductor sensor Temperature measurement range: -20 to 80 ° C - switchable to 0 to 50 ° C Humidity measurement range: 0 to 100% Temperature measurement error: Typical+/-0.5 ° C @ 25 ° C Humidity measurement error: 3% Operating temperature range: -30 to 85 ° C Humidity: 90 Wiring terminal type: Screw clamp clamping range: 0.13 to 1.5mm2 Material: Reinforced polyamide White glass fiber Size: 66 x 60 x 30 mm (height x width x thickness) Weight: 100g # # # Recognized EMC radiation and noise resistance: EN 61326-1: 2006, EN 61326-2-3: 2006 # # # Installation sensor55871+$1150.884910+$1140.422325+$1135.191050+$1129.9597100+$1124.7284150+$1119.4971250+$1114.2658500+$1109.0345 -
![]()
Category: Classification of electronic componentsDescription: Joining sensor for pipe diameters 20 mm → 110 mm, temperature range 0 °C → +200 °C Joining sensor for pipe diameters 20 mm → 110 mm Working temperature range 0 °C → 200 °C Temperature sensor: | 1 x Pt100 cl. B ---|--- Connection: | 2-ltr. circuit Temperature range: | 0°C → 200°C Connecting cable: | 2500 mm TeSi 2 x 0.34 (180°C) Mounting strap: | In the range 20 to 110 mm ### probe48561+$549.407910+$535.075550+$524.0874100+$520.2654200+$517.3989500+$513.57701000+$511.18822000+$508.7995 -
![]()
Category: Classification of electronic componentsDescription: ATEX The screw in PT100 resistance thermometer 354 type resistance thermometer has a replaceable measuring plug for screwing in ATEX II 2/2 G Ex ia IIc T5 Ga/Gb. This thermometer is available in two lengths: 100mm and 200mm ATEX II 2/2 G Ex ia IIc T5 Ga/Gb. It has a protection level of IP54 and meets DIN EN 60 529 measurement range of -40 to+500. The protective tube material is 1 x Pt00. WO， 3 Compliant with DIN EN 60751 3-wire circuit, available in two lengths of 100mm and 200mm # # ATEX resistance thermometer # # # Note stock number 9130810 for 100mm stock number 9130829 for 200mm # # Approved IP54 Compliant with DIN EN 60 529 # # Probe83781+$813.139210+$784.608050+$781.0416100+$777.4752150+$771.7690250+$766.7760500+$761.78301000+$756.0768 -
![]()
Category: Classification of electronic componentsDescription: Type 373 Pt100 resistance thermometer Resistance thermometer for temperature measurement in pipelines and containers High response threshold With built-in transmitter 0 °C → +200 °C, output signal 4 → 20 mA Type: | Pt100 in 2-wire circuit ---|--- Accuracy class: | B Sensor length: | 50 mm (373-E-4/20-0/200-50) | 100 mm (373-E-4/20-0/200-100) Protective tube material: | 1.4571 Head shape: | F or J Thread: | G1 / 2A ### Standard Base Values and Limit Deviations According to DIN EN 60751 # # # Probe20851+$1839.783010+$1823.057725+$1814.695150+$1806.3324100+$1797.9698150+$1789.6071250+$1781.2445500+$1772.8818 -
![]()
Category: Classification of electronic componentsDescription: Type 373 Pt100 resistance thermometer Resistance thermometer for temperature measurement in pipelines and containers High response threshold With built-in transmitter 0 °C → +200 °C, output signal 4 → 20 mA Type: | Pt100 in 2-wire circuit ---|--- Accuracy class: | B Sensor length: | 50 mm (373-E-4/20-0/200-50) | 100 mm (373-E-4/20-0/200-100) Protective tube material: | 1.4571 Head shape: | F or J Thread: | G1 / 2A ### Standard Base Values and Limit Deviations According to DIN EN 60751 # # # Probe81721+$1652.336410+$1637.315225+$1629.804550+$1622.2939100+$1614.7833150+$1607.2727250+$1599.7621500+$1592.2514
