Technical parameters/number of contacts: 25
Technical parameters/capacitors: 4000 pF
Physical parameters/contact material: Copper Alloy
Compliant with standards/RoHS standards: RoHS Compliant
Compliant with standard/REACH SVHC version: 2015/12/17
| Model | Brand | Similarity | Encapsulation | Introduction | Data manual | |
|---|---|---|---|---|---|---|
DB-25P-K87
|
ITT Cannon | 功能相似 | Metal |
ITT CANNON DB-25P-K87 连接器, D sub, 堆叠式, D*系列, DB, 插头, 25 触点, 金属主体, 焊接
|
||
DB-25P-K87
|
ITT Corporation | 功能相似 |
ITT CANNON DB-25P-K87 连接器, D sub, 堆叠式, D*系列, DB, 插头, 25 触点, 金属主体, 焊接
|
|||
DBM25P
|
Cinch Connectivity Solutions | 功能相似 |
ITT CANNON DBM25P 连接器, D-SUB, 公, 25路
|
|||
DBM25P
|
Amphenol | 功能相似 |
ITT CANNON DBM25P 连接器, D-SUB, 公, 25路
|
|||
DBM25P
|
FCI Electronics | 功能相似 |
ITT CANNON DBM25P 连接器, D-SUB, 公, 25路
|
|||
FCE17-B25PM-250
|
Amphenol Commercial Products | 功能相似 |
Amphenol 直向焊槽连接器 这些 Amphenol 滤波 D-Sub FCE17 系列直向引脚或插座连接器采用带有焊杯尾线的面板安装。 过滤器电容 470 pF、820 pF、1000 pF 或 5600 pF 在制造商部件号中可分别由 1、4、5 和 9 表示，例如 FCE17-*****-*X** 固定中心为 25 mm、33.3 mm、47 mm 或 63.5 mm 的 Ø3 mm 安装孔对应的尺寸分别为 E09、A15、B25 和 C37 带有无光泽锡镀层的焊槽接线端子可接受高达 20 awg 的线 绝缘电阻 3000 MΩ 触点电阻 15 mΩ ### 标准 UL94V-0 ### Amphenol Filtered "D" Connectors These filtered connectors are compact interconnect devices that can filter unwanted EMI. The capacitors are mounted inside the connector between each of the contacts and the connector ground shell. They provide: Better EMI Control – With minimized lead inductances and short, direct paths to ground of the filter, performance will typically out perform the same filter components on a P.C.B. by a factor of three to one PCB Space Savings – Incorporating filter elements into the connector, enables simplification of the required filter schematic for the necessary performance plus a savings of 2-4 square inches Cost Savings – Filter elements, such as inductors and capacitors, must no longer be purchased, stocked, assembled or tested. Fewer components means greater reliability at lower cost Easy EMI/RFI Upgrade – These compact filtered connectors fit standard non-filtered connector footprints. For improved EMC performance, simply replace the existing connector with a filtered connector EMC Compliance & Immunity – EMI that is generated from the electronic device, radiated or conducted, will be re-directed to chassis ground through the connector shell. This same device will also protect the system from external EMI/RFI noise (such as radio transmitters, ESD, or natural phenomena such as lightning) in the same way
|
©Copyright 2013-2025 ICGOODFIND (Shenzhen) Electronics Technology Co., Ltd.
The most helpful review