Introduction: Flexlink, also flexlink AB, is a manufacturer of flexible, modular investors and industrial automation equipment, founded in 1980. Headquarters in G ö teborg, Sweden, flexlink has manufacturing, production and engineering facilities in Allentown (USA), pleaska (Poland) and Kuala Lumpur (Malaysia). There are operating units in 27 countries and a global network of Strategic Partners.Altogether FlexLink is present in over 60 countries. Since 2003, FlexLink has been ranked in the world's top 20 largest materials handling system suppliers.
Description:
XC，Gray is equipped with steel rolling ball bearings, which enable users to perform simple linear movements and can construct a mobile frame. The wheel provides regular or center guidance for movement in the XC (11 mm) T-slot. Both wheels come with gasket sleeves, which can be used for direct installation into the T-slot. Provide spare shackle mounting components for installing wheels onto the XC44 beam (non XCBL) end. Wheel bore size (mm)=8.4, yoke center height (mm)=42, yoke width (mm)=44 Linear Motion Components
Description:
Install plates XC, XF, and XD to connect the beam ends to the beam sides. The holes at the end of the beam must be deburred and fixed with screws (M5 rolled). Use countersunk screws to connect the plate to the beam end, and then secure it to the T-shaped groove at the beam end. ###Note: Excluding Fixed Components # # Connection Brackets&Joints - Flexlink Aluminum Structural System
Description:
XD Use XC, 45 °, and 90 ° to establish stable and smooth frame angles. The beam can be precisely cut (45 ° for 90 ° angle; 22.5 ° for 45 ° angle). The corner accessory can be placed in the T-shaped slot and clamped to the slot using the provided kit screws. ###Note includes accessories # # Connection Brackets&Joints - Flexlink Aluminum Structural System
Description:
XC XD is used for end-to-end connection of beams. Especially suitable for using shackles to pull loads. Inventory numbers 261-2166 (4 holes) and 308-0217 (2 holes) include flat head screws, while inventory numbers 331-4093 have two M8 holes
Description:
XD c/w XC When installing the adapter onto the XC beam, use a 37mm wide adapter plate. Excluding fasteners. Each handle requires: 2 M5 ´ 12 set screws, please refer to inventory number 525-824 2 M5 slot nuts, please refer to inventory number 249-0051 for 5.6mm T-slot, inventory number 248-9837 for 11mm T-slot 2 M5 washers, please refer to inventory number 525-931 # # Door&Window Accessories
Description:
XC Suitable for use in conjunction with sliding components (stock numbers 248-9994 and 261-2396), suitable for applications involving high-frequency and load sliding movement, such as constantly moving thrusters or picking and positioning devices. Provided in lengths of 3, 2, and 1m, for fixing at approximately 250mm center, with M6'12 countersunk socket screws, please refer to stock number 210-0269 and M6 T-slot nuts, please refer to stock number 248-9843. End caps are provided without fasteners, and M5 holes are required in the contour and screws # # Linear Motion Components
Description:
XD、XF And XC medium-sized, with height adjustment, used for compensating for floor surfaces, etc. When used with XCBL (lightweight) beams, a bottom plate should be used. According to the needs, deburring beams and rolling threads # # # Feet&Castors
Description:
XD Use XC, 45 °, and 90 ° to establish stable and smooth frame angles. The beam can be precisely cut (45 ° for 90 ° angle; 22.5 ° for 45 ° angle). The corner accessory can be placed in the T-shaped slot and clamped to the slot using the provided kit screws. ###Note includes accessories # # Connection Brackets&Joints - Flexlink Aluminum Structural System
Description:
T The groove nuts XC, XF, and XD can be directly inserted into the T-shaped groove from the beam surface, with spring steel plates used to fix the nut position (even in a vertical position). A regular square nut (thickness 5mm) must be inserted from the end of the beam.
Description:
XF Used to fix the beam structure to the base plate. For lightweight structures, the bracket can replace the support legs. For heavy-duty structures, it can be used in conjunction with adjustable support feet. Including installation of fasteners # # # Note includes accessories # # Connection Brackets&Joints - Flexlink Aluminum Structural System
Description:
XD (22x22) The XF (30x30) can connect the beam end to the beam side. XD to XD, XD to XC, and XF to XF, use M5 self tapping screws to directly install the connectors onto the beam. When the connector is installed on the surface of the beam, the T-shaped fastener will automatically rotate to the T-slot position after tightening the thread of the fastening kit. Including fasteners. ### Door & Window Accessories
Description:
XC Used for flat surfaces, pedals can be used to provide an economical method of installing beams onto the floor. Excluding fasteners. For inventory number 248-9950, please use quantity 1 M8x30 countersunk socket screw (inventory number 210-360) or quantity 4 M6 ´ 30 (inventory number 171-922). For inventory number 261-2188, please use quantity 4 M8x30 or quantity 4 M6x30. The beam end can be cut into squares, deburred, and fixed with rolling threads M8 or M6 as needed. # # # Feet&Castors
Description:
XD、XF And XC medium-sized, with height adjustment, used for compensating for floor surfaces, etc. When used with XCBL (lightweight) beams, a bottom plate should be used. According to the needs, deburring beams and rolling threads # # # Feet&Castors
Description:
XD (22x22) The XF (30x30) can connect the beam end to the beam side. XD to XD, XD to XC, and XF to XF, use M5 self tapping screws to directly install the connectors onto the beam. When the connector is installed on the surface of the beam, the T-shaped fastener will automatically rotate to the T-slot position after tightening the thread of the fastening kit. Including fasteners. ### Door & Window Accessories
Description:
XC Provide sturdy beam end attachments to the floor. Comes with fastening clips for fixing beams and can be self standing or bolted to the floor. Hole size/center (mm): XC44=9/100, XC64=11/180, XC88=13.5/220. ### Feet & Castors
Description:
T The groove washer XC provides the most economical method of connecting beam ends (requires M8 T-shaped groove nuts, stock number 248-9859). A 10mm hole needs to be drilled through the surface of a beam (using a drill fixture, stock number 248-9764). After drilling, the connection position will be determined. For adjustable connections, fastener shackles should be considered.
Description:
XC Used for flat surfaces, pedals can be used to provide an economical method of installing beams onto the floor. Excluding fasteners. For inventory number 248-9950, please use quantity 1 M8x30 countersunk socket screw (inventory number 210-360) or quantity 4 M6 ´ 30 (inventory number 171-922). For inventory number 261-2188, please use quantity 4 M8x30 or quantity 4 M6x30. The beam end can be cut into squares, deburred, and fixed with rolling threads M8 or M6 as needed. # # # Feet&Castors
Description:
XC FlexLink The rotating joint XC allows two XC structural beams to be connected to each other, allowing one beam to swing. Connectors are suitable for paired use to avoid moving loads. The joint should be fixed to the T-shaped groove of each beam with 2 slot nuts (RS stock number 248-9859) and M8x14 DIN7984 socket head screws (note: M8x14 DIN7984 screws are not included and RS currently does not provide them separately). The maximum load for each pair of connectors is 1000N. Linear Motion Components
Description:
XC Suitable for simple door functions. If the hinge is fixed to a flat surface, the detachable T-shaped slot can rotate the position terminal piece. The center of the hole is 50mm, excluding fasteners. Each hinge requires: Quantity 2 M6 ´ 12 socket threads, please refer to inventory number 483-9650 Quantity 2 M6 slot nuts, please refer to inventory number 248-9843 # # # Door&Window Accessories
Description:
T The groove nuts XC, XF, and XD can be directly inserted into the T-shaped groove from the beam surface, with spring steel plates used to fix the nut position (even in a vertical position). A regular square nut (thickness 5mm) must be inserted from the end of the beam.
Description:
Polyamide high load adjustable support foot XC with height adjustment, used for compensating for floor surfaces, etc. When used with XCBL (lightweight) beams, the bottom plate # # # Feet&Castors should be used
Description:
XC、XF XD is used to connect the beam end to the beam side. The holes at the end of the beam must be deburred and fixed with screws (M5 rolled). Use countersunk screws to connect the plate to the beam end, and then secure it to the T-shaped groove at the beam end. ###Note: Excluding Fixed Components # # Connection Brackets&Joints - Flexlink Aluminum Structural System
Description:
XC、XF XD is used to connect the beam end to the beam side. The holes at the end of the beam must be deburred and fixed with screws (M5 rolled). Use countersunk screws to connect the plate to the beam end, and then secure it to the T-shaped groove at the beam end. Note: Connection Brackets&Joints - Flexlink Aluminum Structural System, Excluding Fixed Components
