Description:
5 Pre set 5-digit LED display working mode, start counting, proportional factor programmable single pole conversion relay output timer, with four timing range time relays, programmable with operation and release delay as a time counter plug-in screw terminal connection # # Panel installation 48 x 48- IVO
Description:
LED Display can be used for sequence measurement. Pulse changes can be programmed between 0.0001 and 9999.99. Sensor logic can be programmed. Frequency up to 40 kHz can be measured based on cycle length. Reset LED display. Panel installation: 96x48. Date Freq Tacho. Panel installation
Description:
N 214 series totalising counters Large, 14 mm red LED display. Programmable zero shift. Impulse scaling factor. Dual-voltage meters, selectable by internal switch. Display: | 6 digit, red LED, height 14 mm ---|--- Counting input: | NPN-PNP or NAMUR (by programming) Functions: | Bi-directional counting (2 x 90°), differential (A - B) or summer (A + B) Connection: | screw terminal Dimensions (mm): | 96 x 48 x 121 Panel cut-out (mm): | 45 x 92 Operating temperature: | 0 °C → +60 °C Protection index: | IP 65 front ### Panel installation 96 x 48
Description:
NE131 The series is very suitable for replacing electromechanical counters. Counter and zeroing input 12 → 260 V AC/DC dual 6-digit digital display, used for setting points and current values. Used as a pulse counter or time counter with four resolutions. Non insertable connector with screw terminal block and mounting bracket. Disconnecting Capacity: | Conversion Contact (260 V AC/1 A/150 VA) ------- | --- Input: | 12 → 260 V AC/DC Signal Counting Frequency: | 25 Hz Display: | LCD, 2 rows, 6 digits per row Height: | Height=7mm, Low=4mm Size (mm): | 48 x 48 x 107 Panel Cut (mm): | 45 x 45 Protection Level: | IP 65, Front Operating Temperature: | -10 ° C →+55 ° C # # # Panel Installation 48 x 48
Description:
LED Display can be used for sequence measurement. Pulse changes can be programmed between 0.0001 and 9999.99. Sensor logic can be programmed. Frequency up to 40 kHz can be measured based on cycle length. Reset LED display. Panel installation: 96x48. Date Freq Tacho. Panel installation
Description:
1 Or 2 presets can be selected to display the rate in seconds, minutes, or hours. Integrated 8-bit pulse accumulator # # # Panel installation 48 x 48
Description:
LED Dual preset up/down counter with NPN/PNP or AC logic input to reset front dashboard sealing level IP54 data storage for more than 10 years # # Panel installation 48 x 48- IVO
Description:
F 574 Series 6-digit electro-mechanical totalising counters 6-digit electro-mechanical totalising counters. Counting speed for pulse / pause ratio = 1: \- 20 pulses / sec. in Vdc minimum duration 25 ms / max. unlimited \- 10 pulses / sec. in Vac minimum duration 50 ms/max. unlimited. Supplied with plug-in solder clips. Screw mounting on front face. Consumption: | 2W in Vdc ---|--- Digit height: | 4mm Dimensions (mm): | 50 x 60 x 81 Stock | Reset button | supply voltage ---|---|--- no. | Reset | voltage 163-5944 | With | 24VDC 163-5950 | Without | 220VAC 163-5966 | With | 220VAC ### IVO
Description:
N 214 series totalising counters Large, 14 mm red LED display. Programmable zero shift. Impulse scaling factor. Dual-voltage meters, selectable by internal switch. Display: | 6 digit, red LED, height 14 mm ---|--- Counting input: | NPN-PNP or NAMUR (by programming) Functions: | Bi-directional counting (2 x 90°), differential (A - B) or summer (A + B) Connection: | screw terminal Dimensions (mm): | 96 x 48 x 121 Panel cut-out (mm): | 45 x 92 Operating temperature: | 0 °C → +60 °C Protection index: | IP 65 front ### 面板安装 96 x 48
