Description:
ELT High frequency ballasts are Class I and designed for internal use. This Multipower electronic ballast features ultra-thin low cross-sectional dimensions and operates two T8 lamps. Class I, for internal use ignition, with cathode preheating, for long lamp life, no flicker, constant total power and stable luminous flux, high-frequency operation and high energy efficiency correction. The flicker effect allows for quick connection for 2 hours when using Class I and Class II lamps with input voltage AC/DC 198-264V 350V AC, with fixed spring ballast - lighting components
Description:
ELT LED The LC 116 and LC 125 series of ELT drivers are a series of constant current drivers used for LED modules up to 16W and 25W. Indoor use is equipped with terminal covers and cable clamps for clamping screws on primary and secondary circuits, with a maximum terminal cross-sectional area of 1.5 square millimeters for cables with diameters ranging from 3mm to 8mm. (Secondary circuit) Maximum length of secondary cable: 5m Suitable for installation on wooden surfaces in standby ecological mode ˂ 0.4W high power factor thermal protection overload protection to prevent no-load operation LED module dynamic protection # # # Recognized EN 61347-2-13 EN 62384 EN 61000-3-2 EN 61000-3-3 EN 55015 EN 61547 # # ELT LED driver/power supply
Description:
ELT The DLC 110 series of ELT is a series of dimmable constant current drivers used for LED modules up to 10W. The maximum length of secondary wires for Class II electrical protection rooms equipped with terminal covers and cable clamp systems is 5m, suitable for installation on wooden surfaces. The allowed input voltage is AC/DC: 198-264V, 0/50-60Hz. (DC/AC) High power factor overload protection, short circuit protection, and prevention of no-load operation are allowed for DLC models of dimmers: rear and front edge dimming with a range of 5% to 100%. # # # Approved EN-61347-2-13 EN-62384 EN-61000-3-2 EN-61000-3-3 EN-55015-3-2 EN-61547 ### ELT LED Driver/Power Supply
Description:
ELT LED The LC 116 and LC 125 series of ELT drivers are a series of constant current drivers used for LED modules up to 16W and 25W. Indoor use is equipped with terminal covers and cable clamps for clamping screws on primary and secondary circuits, with a maximum terminal cross-sectional area of 1.5 square millimeters for cables with diameters ranging from 3mm to 8mm. (Secondary circuit) Maximum length of secondary cable: 5m Suitable for installation on wooden surfaces in standby ecological mode ˂ 0.4W high power factor thermal protection overload protection to prevent no-load operation LED module dynamic protection # # # Recognized EN 61347-2-13 EN 62384 EN 61000-3-2 EN 61000-3-3 EN 55015 EN 61547 # # ELT LED driver/power supply
Description:
ELT High frequency ballast, Class I, for built-in use. This ultra-fine thin section electronic ballast can operate T5 lamps. Class I, for internal use ignition, with cathode preheating, for long lamp life, no flicker, constant total power and stable luminous flux, high-frequency operation and high energy efficiency correction. The flicker effect allows for quick connection for 2 hours when using Class I and Class II lamps with input voltage AC/DC 198-264V 350V AC, with fixed spring # # # ballasts - lighting components
Description:
T5 Fluorescent lamp ELT high-frequency ballast, Class I, for built-in use. This electronic ballast can operate T5 fluorescent lamps. Class I, for internal use ignition, with cathode preheating, for long lamp life, no flicker, constant total power and stable luminous flux, high-frequency operation and high energy efficiency correction. The flicker effect allows for quick connection for 2 hours when using Class I and Class II lamps with input voltage AC/DC 198-264V 350V AC, with fixed spring # # # ballasts - lighting components
