Introduction: Parker-Hannifin Corporation, originally Parker Electric Company, often referred to as Parker, is an American company specializing in motion and control technology. The company was founded in 1917. Its corporate headquarters is in Cleveland, Ohio, and has been publicly traded on the New York Stock Exchange since December 9, 1964. The company is motion control technology (including aerospace, climate control, electromechanical, filtered fluid and gas processing, hydraulic, pneumatic, process control, and sealing and shielding.
Description:
EO® Metric Tube Fitting - Elbows&Tees Ermeto Original or EO is a registered trademark of Parker Ermeto GmbH ® progressive ring fittings, for metric tube, are manufactured from mild steel, with zinc plated and passivated finish. They are available in light duty and heavy duty series to cover a wide range of pressure ratings. Each fitting comes with a tube nut but the bite ring will need to be ordered separately. The progressive ring bite produces a keyed leak-free tube connection. The range of fittings is intended purely for the assembly of connections for fluid applications. All fittings are supplied with an instruction leaflet. For steel fittings it is recommended that seamless drawn steel tubes to DIN 2391/C are used. Operating temperature range without pressure reductions for the steel fitting materials is -40 °C to +120°C.
Description:
A-LOK® The dimensions A and C on the drawing of the straight connector # # are typical finger tightening types. ### A-LOK ® The Parker Hannifin series of stainless steel instrument tubes, fittings, valves, regulators, and manifolds are manufactured to meet the requirements of the highest quality precision instrument components. All products meet or exceed relevant global standards. A-LOK ® Double ring stainless steel fittings are used for instrumentation applications that require high-quality, leak proof pipe components. O - HCT standard o - Pipe size and thread identification o - Adopting Supercase ™ Ring hardening process
Description:
A-LOK® The dimensions A and C shown on the drawing for the pipe to pipe joint # # # are typical finger tightening types. ### A-LOK ® The Parker Hannifin series of stainless steel instrument tubes, fittings, valves, regulators, and manifolds are manufactured to meet the requirements of the highest quality precision instrument components. All products meet or exceed relevant global standards. A-LOK ® Double ring stainless steel fittings are used for instrumentation applications that require high-quality, leak proof pipe components. O - HCT standard o - Pipe size and thread identification o - Adopting Supercase ™ Ring hardening process
Description:
P1D - Parker's P1D-T series tie rod pneumatic actuators fully comply with ISO15552 (ISO 6431 and CETOP RP52P) standards, simplifying installation and ensuring global compatibility. P1D-T has a magnetic piston and comes standard with a fully adjustable stroke buffer end. ###Features and advantages: Standard galvanized steel end cap nut, standard zinc nickel piston rod nut, standard stainless steel piston rod. Metal polymer piston rod bearings, metal buffer pistons come standard with anodized sleeves, stainless steel tie rods, aluminum end caps, magnetic pistons, Parker P1D 32-63mm diameter technical parameters - * * medium * * | compressed air, filtered, lubricated or non lubricated * * working temperature range * * | maximum 10 bar * * ambient temperature range * * | maximum -20 ° C to+70 ° C * * end caps * * | die cast zinc * * sleeves * * | hard anodized aluminum * * pistons * * | stainless steel (303S31) * * tie rods * * | galvanized steel * * sealing rings * * | polyurethane
Description:
P1D-S Cylinder Parker P1D - Standard series ISO cylinder suitable for medium load operation, standard configuration includes a magnetic piston that can work without lubrication. P1D - The standard ISO cylinder is dual operated, providing adjustable end buffering with an inner diameter size range of 32mm to 125mm. All P1D - standard series cylinders include self-lubricating HDPE scraper rings and piston rod seals, which can perform drying operations during applications where the lubricating grease film on the piston rod is regularly flushed away. P1D - Standard cylinder manufactured with initial non-toxic food industry certified transparent grease, free of PTFE and silicone resin. ###Note that if operating P1D cylinders in applications where there may be significant lateral loads on the piston rod, external guides should be used in conjunction with them. The use of P1D cylinders without external guide rails may reduce the working life of the device. ###Standard ISO 6431; ISO 15552； VDMA 24562； AFNOR Installation Size Standard # # # Parker P1D 32-63mm Diameter Technical Parameters - * * Medium * * | Compressed air, filtered, lubricated or non lubricated * * Operating temperature range * * | Maximum 10 bar * * Environmental temperature range * * | Maximum -20 ° C to+70 ° C * * End cap * * | Die cast zinc * * sleeve * * | Hard anodized aluminum * * piston * * | Stainless steel (303S31) * * tie rod * * | Galvanized steel * * sealing ring * * | Polyurethane
Description:
1.2W Low power solenoid valve controller, requires separate order of non locking manual override IP65 protection level * * Description * * | * * Medium * * | * * Working pressure * * | * * Working temperature (° C) * * | * Flow rate G 1/2 * * | * Flow rate G * * * * * 1/4 * * -----------------------------------------------------------------------------------------. Electromagnetic coil controller and connector plug must be ordered. ###Maxam, Norgren, and Parker (V.S.A.) warn that although compressed air is often considered a safe energy source, it must be treated with caution. Under no circumstances should it be used without special purpose.
Description:
lokCone pipe fittings and water pressure pipes # # # Cone pipe fittings Triple Lok 37 ° expansion fittings are suitable for use with metric pipes. Their simplicity, compact design, and easy assembly make them a wide choice for fluid power applications in motion control. Steel fittings are particularly suitable for low and medium pressure applications with a rated pressure of up to 350 bar, with a working temperature range of -40 ° C to+120 ° C. Their design is simple. The expansion tool pliers and expansion pins (provided separately) form a seal and maintain liquid under system pressure. The pipe end has a 37 ° expansion and is clamped between the fitting mouth and the sleeve when the nut is tightened. This provides an effective single sealing point between the accessory and the pipe expansion. The Parker Triple Lok accessory consists of three components: accessory body, pipe nut, and sleeve. For steel fittings, it is recommended to use seamless drawn steel pipes according to DIN 2391/C.
Description:
2 The two-way ball valve with BSP parallel straight thread connection at both ends is suitable for sealing nitrile valve stems for petroleum based hydraulic fluids, lubricants, fuels, and air, Delrin ® Spherical valve seat Delrin ® It is a trademark registered by Du Pont for its formaldehyde resin # # Ball Valves
Description:
Banjo The plug-in terminal is BSP parallel threaded, with port sealing, and can achieve EO through hardened sealing rings ® It is a registered trademark of Parker Ermeto GmbH. Banjos, Bite Rings & Tube Nuts Ermeto Original or EO ® progressive ring fittings, for metric tube, are manufactured from mild steel, with zinc plated and passivated finish. They are available in light duty and heavy duty series to cover a wide range of pressure ratings. Each fitting comes with a tube nut but the bite ring will need to be ordered separately. The progressive ring bite produces a keyed leak-free tube connection. The range of fittings is intended purely for the assembly of connections for fluid applications. All fittings are supplied with an instruction leaflet. For steel fittings it is recommended that seamless drawn steel tubes to DIN 2391/C are used. Operating temperature range without pressure reductions for the steel fitting material is -40 °C to +120°C.
Description:
2 The two-way ball valve with BSP parallel straight thread connection at both ends is suitable for sealing nitrile valve stems for petroleum based hydraulic fluids, lubricants, fuels, and air, Delrin ® Spherical valve seat Delrin ® It is a trademark registered by Du Pont for its formaldehyde resin # # Ball Valves
Description:
FULFLO Polypropylene 10 in. wrapped depth filter cartridge 1 in. ID and 2 1/2 in. outer diameter made of FDA certified material for contact with liquids intended for drinking and consumption, in compliance with CFR Title 21 for effective removal at rated 90% efficiency # # Filtration # #
Description:
EO® Metric Tube Fitting - Elbows&Tees Ermeto Original or EO is a registered trademark of Parker Ermeto GmbH ® progressive ring fittings, for metric tube, are manufactured from mild steel, with zinc plated and passivated finish. They are available in light duty and heavy duty series to cover a wide range of pressure ratings. Each fitting comes with a tube nut but the bite ring will need to be ordered separately. The progressive ring bite produces a keyed leak-free tube connection. The range of fittings is intended purely for the assembly of connections for fluid applications. All fittings are supplied with an instruction leaflet. For steel fittings it is recommended that seamless drawn steel tubes to DIN 2391/C are used. Operating temperature range without pressure reductions for the steel fitting materials is -40 °C to +120°C.
Description:
14P1 These filters are designed to operate in industrial and mobile hydraulic systems. They will protect hydraulic components from particle contamination. Minimum static pulse 1240 Bar. Standard bypass valve with visual filter condition indicator installed at both ends of the filter head. The filter cartridge has been tested according to ISO 4572 multi-channel testing and a spare filter cartridge is provided High Pressure Filters designed for use in high pressure hydraulic systems. Installed downstream of the pump, they protect critical hydraulic components against dirt and other foreign matter generated within the pump. These filters have a maximum working pressure of 414 bar, a safety factor of 3:1 and an operating temperature of -40 °C to +121° C. Filter heads are manufactured from SG Iron with a steel filter bowls. Fitted with a high efficiency high capacity 10 micron element as standard
Description:
BSP Parallel thread adapter. The Parker K series adapters are manufactured in accordance with the BS5200 standard and are designed for use with BSP sealed hose rotary connectors. The Parker K4 adapter series can be used with Parker D9/92, B1, B2, and B4 adapters. By bonding seals, linear fittings can also be used for adapters with ISO 1179-1/DIN 3852 ports. ###Note for adapters of various sizes, suitable for low voltage ratings. **The K4 adapter cannot be interchanged with JIS P4 accessories. **# # # Straight pipe adapter and plug BSP parallel thread adapter. Made of steel, complying with BS 5200, with a zinc chromate yellow surface to provide high corrosion resistance (500 hour salt spray test). All adapters have a working temperature range of -40 to+120 ° C (-3 to+120 ° C for plugs). The female 60 ° cone makes these adapters ideal port fittings, suitable for use with our various BSP reusable fittings and crimped hose assemblies. Warning: The hydraulic system can operate under high pressure, and accessories and adapters can be subjected to extreme loads such as vibration and free pressure peaks. When selecting accessories or adapters, special attention should be paid to technical specifications.
Description:
381 High quality elastic hose is suitable for high-pressure service synthetic rubber external hose, reinforced with high tension steel wire. Lining, Buna N (nitrile) is suitable for use with Series 30 reusable accessories, with a temperature range of -40 ° C to+100 ° C. Applications include high-pressure services with oil seats, water ethylene glycol and water oil emulsion hydraulic fluids, hot oil, grease, lubricants, natural substances and fuel, air and water. The coil provides 5m coils and exceeds the following manufacturing standards: to DIN 20022 2SN-SAE 100 R2AT-150 1436/11 pin piercing protective cover, for air or gas applications, above 14 bar (200 psi). Chemical reagents in all mineral based liquids may be harmful to the impedance of hose materials * * Suitable accessories - crimping * * -48 series, 43 series and 71 series # # # # Injection non stripping hose type 381 is not suitable. Used together with Parker series high-pressure hydraulic cylinders and pumps, their working pressure is 700 bar. The displayed work pressure represents the dynamic pressure system.
Description:
Parker Type 301 non stripping rubber hose, with BSP straight rotating containment at each end. The temperature range is -40 to+100 ° C. All surface treatment assemblies undergo a maximum double working pressure test pressure. The temperature range is -40 to+100 ° C. Note that these components are not suitable for use with our high-voltage hydraulic air and pump (working pressure of 700 bar) series. They are not included in the BS 5750 Part 2 Retailer Clause that has been registered and evaluated for capacity level B. Pin prick protective cover, used for air or gas applications, above 17 bar (250 psi). Standard DIN 20022 2SN, EN853-2SN, SAE 100R2 AT Crimped Hose Assemblies
Description:
lokCone fittings and water pressure pipe cone fittings Triple Lok 37 ° expansion fittings are suitable for use with metric pipes. Their simplicity, compact design, and easy assembly make them a wide choice for fluid power applications in motion control. Steel fittings are particularly suitable for low and medium pressure applications with a rated pressure of up to 350 bar, with a working temperature range of -40 ° C to+120 ° C. Their design is simple. The expansion tool pliers and expansion pins (provided separately) form a seal and maintain liquid under system pressure. The pipe end has a 37 ° expansion and is clamped between the fitting mouth and the sleeve when the nut is tightened. This provides an effective single sealing point between the accessory and the pipe expansion. The Parker Triple Lok accessory consists of three components: accessory body, pipe nut, and sleeve. For steel fittings, it is recommended to use seamless drawn steel pipes according to DIN 2391/C.
Description:
AISI 303 Stainless steel standard ISO 7241-B Parker 60 Series Zinc plated/yellow chromate steel, AISI 303 stainless steel or brass Quick Action couplings fitted with NBR (Nitrile) seals. BSPP Thread sizes Hardened nipples and sleeves High flow capacity High pressure seal design Captive valve seal Durable ball locking mechanism Temperature range: -40 to +80 °C
Description:
Sensocontrol Sensocontrol is a modern diagnostic measurement system that is very robust and insensitive to dust, making it suitable for extreme situations. The device can automatically identify the connected sensor and display the correct unit and scale of the corresponding sensor on the large display screen. The unit of measurement with the display provides two sensor input 9V battery (IEC 6F22) power supplies, with a sensor data output for about 10 hours of operation for printers and PCs. The low power consumption with an auxiliary adapter means that it can be used for a long time without relying on the power supply. The battery capacity displays LO BAT and automatically disconnects the power supply 15 minutes later, which can be carried with you, or used as a desktop device. It is provided with an integrated bracket in a sturdy plastic suitcase, with a molded foam plug-in. The introduction of the second pressure sensor and adapter enables Sensocontrol to generate a differential pressure value Sensocontrol kit from the sensor signal Including hand instrument, 0-600 bar pressure transducer, with fixed cable connection and one BPS to M16 Adapter, easy to connect to available test points or free port instrument size 145 x70 x 40mm Note * * RS 247-8540 Diagnostic Equipment - Digital
Description:
BSP Parallel thread adapter. The Parker K series adapters are manufactured in accordance with the BS5200 standard and are designed for use with BSP sealed hose rotary connectors. The Parker K4 adapter series can be used with Parker D9/92, B1, B2, and B4 adapters. By bonding seals, linear fittings can also be used for adapters with ISO 1179-1/DIN 3852 ports. ###Note for adapters of various sizes, suitable for low voltage ratings. Warning: The hydraulic system can operate under high pressure, and accessories and adapters can be subjected to extreme loads such as vibration and free pressure peaks. When selecting accessories or adapters, special attention should be paid to technical specifications.
Description:
tabe Medium and double clamp options with polypropylene clamp body, welded metal plate with strip steel, galvanized steel nail metal plate, and M6 x 30mm galvanized steel clamp screw. The clamp body in two equal diameter valves has a ribbed inner diameter, which can safely fix the metal pipe while ensuring high sound insulation and reducing vibration. Working temperature range: -30 ° C to+90 ° C # # # Tube Clamp
Description:
BSP Parallel thread adapter. Made of steel, complying with BS 5200, with a zinc chromate yellow surface to provide high corrosion resistance (500 hour salt spray test). All adapters have a working temperature range of -40 to+120 ° C (-3 to+120 ° C for plugs). The female 60 ° cone makes these adapters ideal port fittings, suitable for use with our various BSP reusable fittings and crimped hose assemblies. Warning: The hydraulic system can operate under high pressure, and accessories and adapters can be subjected to extreme loads such as vibration and free pressure peaks. When selecting accessories or adapters, special attention should be paid to technical specifications.
Description:
EO® It is a registered trademark of Parker Ermeto GmbH. ###Metric pipe fittings - Ermeto original or EO straight pipe fittings ® Progressive ring fittings, used for metric pipelines, made of low carbon steel, with galvanized and passivated surfaces. They offer both low load and high load series, covering a wide range of rated pressures. Each accessory comes with a pipe nut, but the bite ring needs to be ordered separately. Progressive ring biting can produce key controlled leak free pipeline connections. This series of accessories is specifically designed for connecting and assembling, suitable for liquid applications. All accessories come with instruction manuals. For steel fittings, it is recommended to use seamless drawn steel pipes that comply with DIN 2391/C. For steel assembly materials, the working temperature range without pressure reduction is -40 ° C to+120 ° C. Warning: Hydraulic systems can operate under high pressure. To ensure EO ® The practical safety of pipeline fittings is limited to EO ® Partially applied to their assembly and should not exceed pressure and rated temperature.
Description:
Parkers K The series adapter is manufactured in accordance with BS5200 standard and designed for use with BSP sealed hose rotary connectors. The Parker K4 adapter series can be used with Parker D9/92, B1, B2, and B4 adapters. By bonding seals, linear fittings can also be used for adapters with ISO 1179-1/DIN 3852 ports. Note: The K4 adapter cannot be interchanged with JIS P4 accessories. Bend and T-shaped adapter BSP parallel thread adapter. Made of steel, complying with BS 5200, with a zinc chromate yellow surface to provide high corrosion resistance (500 hour salt spray test). All adapters have a working temperature range of -40 to+120 ° C. The female 60 ° cone makes these adapters ideal port fittings, suitable for use with our various BSP reusable fittings and crimped hose assemblies.
Description:
AISI 303 Stainless Steel # # # Standard ISO 7241-B ### Parker 60 Series Zinc plated/yellow chromate steel, AISI 303 stainless steel or brass Quick Action couplings fitted with NBR (Nitrile) seals. BSPP Thread sizes Hardened nipples and sleeves High flow capacity High pressure seal design Captive valve seal Durable ball locking mechanism Temperature range: -40 to +80 °C
Description:
Parker Valves and electrical contact blocks. The modular structure of valves and contact blocks allows for flexible configuration. High quality fluororubber seals provide reliability for your pneumatic installation. Modular structure. Components must be ordered separately with 4mm, 3/2 normally open or normally closed valves. Each actuator can have up to 3 valves or contact blocks. Electrical contacts and pneumatic valves with a diameter of 22mm can be operated simultaneously through electrical contact blocks. Contact rating: 240V AC 3A. High quality manual operation slide valve fluororubber seal suitable for positive pressure or vacuum equipment applications. Medium | Compressed air. Filtering, lubrication or non lubrication - | - working pressure | 1 to 9 bar working temperature range | -15 ° C to+60 ° C flow rate | 60 L/min port connection | 4mm push in electrical contact | is the # # # injection control device that provides more actuator switches. ###Buttons and selectors - Parker and Schneider Electric
Description:
Parkers K The series adapter is manufactured in accordance with BS5200 standard and designed for use with BSP sealed hose rotary connectors. The Parker K4 adapter series can be used with Parker D9/92, B1, B2, and B4 adapters. By bonding seals, linear fittings can also be used for adapters with ISO 1179-1/DIN 3852 ports. Note: The K4 adapter cannot be interchanged with JIS P4 accessories. Bend and T-shaped adapter BSP parallel thread adapter. Made of steel, complying with BS 5200, with a zinc chromate yellow surface to provide high corrosion resistance (500 hour salt spray test). All adapters have a working temperature range of -40 to+120 ° C. The female 60 ° cone makes these adapters ideal port fittings, suitable for use with our various BSP reusable fittings and crimped hose assemblies.
Description:
0.5 bar Rupture pressure Flow Control Valves Single acting and double acting in-line flow control valves. Single acting valves allow flow control in one direction and free flow in the opposite direction. Double acting valves allow flow control in both directions.
Description:
ISO 7241-B ### Parker 60 Series Zinc plated/yellow chromate steel, AISI 303 stainless steel or brass Quick Action couplings fitted with NBR (Nitrile) seals. BSPP Thread sizes Hardened nipples and sleeves High flow capacity High pressure seal design Captive valve seal Durable ball locking mechanism Temperature range: -40 to +80°C
